SpeedPlus9
Feature Counter & hardware

Label roll, ribbon and sticker checks

Load the roll and ribbon the right way, and fix crooked, half or blank stickers one cause at a time. Most blank or crooked stickers after a roll change come from a roll or ribbon loaded the wrong way. A barcode label printer holds two things: the label roll that is printed on, and the ribbon whose ink makes the print. They take different paths.

On this page

12.12Loading the Label Roll and Ribbon

Most blank or crooked stickers after a roll change come from a roll or ribbon loaded the wrong way. A barcode label printer holds two things: the label roll that is printed on, and the ribbon whose ink makes the print. They take different paths. Each model differs a little, so keep its guide at hand; this order fits most.

  1. Open the cover. Switch the printer off. Press the locks on both sides and lift the top cover. The roll goes below, the ribbon above.
  2. Load the roll. Put the roll on its holder with the labels facing up. Pull the end out through the front slot. Slide both guides against the edges of the roll. Loose guides make crooked stickers.
  3. Load the ribbon. On most printers the full ribbon goes on the back spindle and an empty core on the front one. Pass the ribbon under the print head, tape its end to the empty core and turn it two rounds. The ink side must face the label: press the sticky side of a spare label on the ribbon; the side that leaves ink on it is the ink side.
  4. Close and calibrate. Press the cover down on both sides until it clicks, then switch on. Calibration teaches the printer where one sticker ends. On many printers you hold the Feed button until a few labels move out; your guide gives the exact way.
  5. Print one test sticker. On the Barcode Labels screen tick one row, set its Qty to 1, press Sticker Print and Print (12.4). Check that the print sits in the middle of the label, then scan it.
Example Kaur Ladies Garments puts in a new roll of 50 × 25 mm labels. The first test sticker prints half on the gap between two labels. She holds the Feed button until the printer stops on a gap, prints one more test sticker, and it comes out centred. Then she prints the 120 labels for the day's purchase.

Read every step in the guide: Barcode Printing, section 12.12

12.13Stickers Crooked, Half or Blank: Five Checks

A sticker printed crooked, half, or across two labels wastes the roll. There are five common causes. Fix one at a time, and after each fix print one sticker, not the whole roll.

CheckWhat to look at and fix
1. Label size in WindowsMeasure one sticker, width and height, with a ruler. In the Windows printers list open your label printer → Printing Preferences and type the measured size. Measure; do not guess.
2. CalibrationThe printer finds the gap between stickers and stops there. After a new roll it may need to learn the gap again (12.12, step 4). Signs: print runs across two stickers, or every second sticker comes out blank.
3. Size in Speed PlusHelp → Barcode Sticker Studio, open your design: W mm, H mm, Across, Gap X, Gap Y and the margins must match the roll and the size in check 1. Keep empty space round the barcode and do not crowd the sticker. Look at the sticker in the middle of the Studio, then press Save Design (12.7).
4. RibbonWhite lines across the sticker: the ribbon is creased; straighten it and wind it tight. A fully blank sticker: the ribbon is in the wrong way round, ink side away from the label.
5. Darkness and speedIn Printing Preferences. Faint print: raise the darkness a little. Bars running into each other: lower it. A slower speed often gives a cleaner barcode.
Example Stickers of a 38 × 25 mm roll come out cut at the bottom. The owner measures a sticker: 38 × 25 mm. Printing Preferences says 40 × 30 mm. He corrects it to 38 × 25, prints one test sticker, and it fits. Cost of finding the fault: one sticker, not a roll of 1,000.

Read every step in the guide: Barcode Printing, section 12.13

Questions and answers

The labels print shifted on the roll.

Open the design in Help → Barcode Sticker Studio and set W mm, H mm, Gap X, Gap Y and the margins to your real sticker. Also check the label size set for the printer in Windows and calibrate the printer. The five checks are in 12.13.

The stickers come out completely blank.

The ribbon is in the wrong way round, with the ink side away from the label. Load it again (12.12). With direct thermal labels, check that the label side faces the print head.

One sticker prints across two labels, or every second label is blank.

The printer has lost the gap between labels. Calibrate it (hold the Feed button on most printers; see its guide), then print one test sticker.

White lines run across my stickers.

The ribbon is creased. Straighten it and wind it tight on the core. If the lines stay in the same place on every sticker, ask the printer service to look at the print head.

Do I need a ribbon?

For ordinary paper or plastic labels, yes. Direct thermal labels need none: if a label turns dark when you scratch it, it is direct thermal.

How do I test before printing a whole roll?

On the Barcode Labels screen tick one row, set Qty to 1, press Sticker Print, Preview and Print. Scan the sticker; if the right item comes up, print the rest.

Watch it

Test One Barcode Sticker Before Printing the Roll

Barcode & labels·Short

See this feature working.

Tell us your trade and how you bill today. We will show you the same work in Speed Plus 9, on a call or at your shop.